Structural glazing and stick curtain walls compared
A building’s facade has to balance appearance, weather protection, structural movement, energy performance and construction logistics. Two systems often considered for glazed commercial and residential envelopes are structural glazing and stick system curtain walls. They can produce similar levels of transparency from a distance, yet their framing, glass retention, installation sequence and maintenance requirements are substantially different.
For Australian developers, architects and main contractors, the decision should reflect the project’s climate, height, wind exposure, programme and access arrangements. A glazed facade in Sydney’s coastal environment will face different conditions from one in Perth, Brisbane or Melbourne, while projects in Darwin and northern Queensland require particularly careful attention to solar gain, humidity and severe wind events.
How the two facade systems are built
A stick curtain wall is assembled on site from individual vertical mullions, horizontal transoms, glass panels, pressure plates, cover caps, gaskets and spandrel elements. The mullions and transoms form the visible grid, while mechanical pressure plates and caps hold the infill panels against the framing. Seals and drained cavities manage water that passes the outer weather seal.
This approach gives installers flexibility. Openings can be checked and adjusted progressively, and individual components can often be delivered through constrained access routes. It is well suited to medium-sized developments, irregular floor plates and projects where site teams need to accommodate dimensional variations in the structure.
Structural glazing presents a cleaner external appearance because the glass is bonded to carrier frames with a structural silicone joint. From outside, the facade may appear as a continuous glass surface with narrow shadow lines between panes. The system still relies on an aluminium framing structure behind the glass, but the external pressure caps and cover plates found on conventional curtain walls are largely concealed.
The bonding process introduces stricter factory and site controls. Glass units, frames, silicone compatibility, bond dimensions, curing times and substrate preparation must be documented. Structural silicone glazing is therefore less forgiving of rushed installation or uncontrolled weather conditions than a conventional pressure-plated system.
Visual character and architectural freedom
The most obvious difference is the external expression. Stick curtain walls usually reveal the mullion and transom grid, which can become a deliberate part of the building’s rhythm. Caps are available in different profiles and finishes, including anodised aluminium and powder coating, so the system can complement masonry, metal cladding or precast concrete.
Structural glazing creates a flatter, more uniform facade. It can support large areas of uninterrupted glass, strong horizontal or vertical emphasis and carefully controlled shadow gaps. This is attractive for office foyers, apartment common areas, retail frontages and architectural features where the designer wants the glazing to read as a single plane.
The design freedom is not unlimited. Glass size, thickness, weight, wind pressure, edge clearances and allowable deflection still govern the facade. Solar control glass, low-emissivity coatings, fritting and ceramic patterns may be needed to manage glare and heat. In Australia, high-performance glazing should be coordinated with the National Construction Code energy provisions and the project’s whole-building thermal model rather than selected for appearance alone.
Specialist product research is useful when a project needs a concealed external frame. For example, this overview of Kawneer 1600 SG explains the type of considerations that apply when specifying a structural glazing curtain wall, including aesthetics, performance and installation requirements.
Weather, wind and thermal performance
Both systems can be designed to resist air infiltration, water penetration and wind loads, but their performance depends on the complete facade build-up. Drainage paths, pressure equalisation, sill flashings, end dams, corner details and interfaces with roofs and walls are often more important than the system label itself. A visually sophisticated facade can still fail if water is trapped at a slab edge or if movement joints are poorly coordinated.
Wind design is particularly important in exposed Australian locations. Tall buildings in Sydney, Melbourne and Perth may experience substantial wind pressures, while cyclone regions in northern Queensland, the Northern Territory and northern Western Australia require design and certification for more severe conditions. Structural calculations typically need to consider the requirements of the NCC and relevant Australian Standards, including wind actions under AS/NZS 1170.2 where applicable.
A stick wall accommodates movement through mullion joints, transom connections, gaskets and glazing pockets. Structural glazing uses flexible silicone joints and carefully designed frame interfaces to tolerate thermal and structural movement. Both systems need allowances for slab deflection, inter-storey drift and differential expansion between aluminium, glass and adjacent materials.
Thermal performance is affected by frame depth, thermal breaks, glass specification, spandrel zones and the ratio of vision glass to opaque facade. Brisbane projects may need strong solar control to reduce cooling loads, while Melbourne projects may place greater emphasis on winter heat retention. Coastal sites also require appropriate finishes and corrosion considerations, particularly where salt-laden air reaches exposed aluminium or fixings.
Installation, quality control and site conditions
Stick curtain walls are commonly installed floor by floor. Mullions are fixed to anchors, transoms are connected, gaskets are inserted and glass or panels are placed as the building progresses. This sequence can suit Australian construction programmes where trades work around concrete tolerances, internal fit-outs and changing delivery schedules.
The trade-off is that more work takes place at height and on the building site. Weather, handling damage, sealant contamination and inconsistent gasket installation can affect quality. Protection is essential in busy areas such as Sydney or Melbourne CBD sites, where facade components may be stored beside active delivery routes and pedestrian management zones.
Structural glazing usually involves a higher proportion of controlled fabrication away from the site. Carrier frames and glass panels can be prepared under repeatable conditions, allowing close control of silicone application and curing. Site installation may then be quicker, although the tolerances for receiving anchors, brackets and adjoining construction must be carefully managed.
A project-specific inspection and test plan should cover material certificates, glass identification, silicone batch records, adhesion tests, joint dimensions, drainage paths and water testing. The facade should also be coordinated with fire stopping at slab edges, acoustic requirements, balustrades, shading devices and internal finishes. A reference such as the Smithfield project demonstrates how a completed building envelope package can bring multiple facade trades and interfaces into a coordinated result.
Cost, maintenance and selection criteria
Initial cost comparisons should include design, engineering, fabrication, access, testing, replacement and long-term cleaning. Stick systems can be economical where the building has repetitive bays and straightforward access, especially when local installation labour and standardised components are readily available. They can also make future replacement of a single panel relatively direct.
Structural glazing may carry higher fabrication and quality-control costs, particularly for bespoke geometries, oversized units or complex glass compositions. However, the cleaner elevation can reduce visual clutter and support a premium architectural brief. Where a large proportion of the facade is repetitive, factory-controlled production may help offset some of the additional detailing and handling requirements.
Maintenance differs in character rather than disappearing. Stick walls expose pressure plates, caps and gaskets that may be accessible for inspection or replacement. Structural glazing places greater reliance on the condition of silicone weather seals and structural bonds. Periodic inspections should look for sealant cracking, adhesion loss, glass damage, staining, blocked drainage and movement at interfaces.
The choice should therefore be made through a coordinated performance review. Consider the desired external expression, building height, wind region, glass size, thermal targets, fire strategy, access equipment, programme and local maintenance capability. Roof and facade drainage also need to be commissioned as part of the envelope package; practical guidance on roof drainage testing can help teams plan verification after installation.
For many Australian projects, a hybrid solution may be appropriate. Conventional stick curtain walling can provide cost-effective glazing across regular elevations, while structural glazing can mark entrances, atria or feature zones. The strongest outcome comes from selecting the system around measurable performance and buildability, then coordinating the glazing, cladding, roofing and architectural interfaces from early design through handover.