Specifying silicone gaskets for leak-free curtain wall joints

Curtain wall leakage is rarely caused by one dramatic defect. Water usually enters through a combination of small weaknesses: an incorrectly compressed gasket, a poorly formed corner, blocked drainage paths, movement beyond the joint’s capacity, or an incompatible sealant. Silicone gaskets can provide a durable weather seal, but only when their material, profile and installation method are specified as part of the complete facade system.

For Australian projects, the specification must account for intense ultraviolet exposure, high summer temperatures, wind-driven rain and significant differences between coastal, inland and tropical environments. A curtain wall on a Melbourne office may face cold winters and strong seasonal movement, while a Darwin or Cairns facade must deal with humidity, cyclonic wind actions and frequent heavy rain. The same gasket detail should not be copied across every project without checking the site conditions.

The best result comes from coordinating the gasket with aluminium mullions, transoms, glass, pressure plates, spandrel panels, flashings and drainage cavities. Developers, architects and head contractors also need clear responsibility for design tolerances, factory fabrication, site installation and testing. A complete envelope contractor such as Bak Cladding Solutions can help align these details from material selection through to handover.

A good specification therefore does more than state “silicone gasket to suit.” It identifies the rubber compound, hardness, geometry, compression range, joint movement, corner treatment, compatibility requirements and inspection criteria. These details reduce ambiguity during procurement and give the installation team a practical benchmark for quality.

Start with the curtain wall’s drainage strategy

A curtain wall is generally designed as a pressure-equalised or drained system rather than a single impermeable barrier. The outer gasket limits the volume of water entering the glazing pocket, while internal seals and pressure plates control air movement. Any water that reaches the drainage cavity must be directed through weep holes, slots and sill flashings to the outside.

A gasket should never be selected in isolation from this arrangement. Excessive compression can distort the profile and close a drainage path, while insufficient compression can leave a discontinuous seal at the glass edge. The detail should show the intended contact surfaces, the direction of drainage and the location of every required joint or splice. For a useful comparison between gasket-based interfaces and bonded glazing, review this structural glazing guide while developing the facade concept.

The specification should also distinguish between the external weather seal, internal air seal and any glazing wedge or pressure plate gasket. Each component may have a different profile and performance role. Treating all of them as interchangeable can create a hidden bypass route from the exterior to the building interior.

At sill zones, corners and changes in level, the drainage strategy requires particular attention. Weep holes must remain open after installation, and gasket ends should not obstruct them. A drawing that indicates “continuous gasket” without showing how continuity interacts with drainage can lead to water being trapped inside the frame.

Select the right silicone rubber compound

Silicone rubber is valued for its resistance to ultraviolet radiation, ozone, temperature variation and long-term weathering. Those properties make it well suited to exposed curtain wall joints in Australia, where direct sun can heat dark aluminium frames and west-facing elevations can experience severe thermal cycling. The gasket must still be manufactured to a suitable grade, with documented performance and consistent dimensions.

Specify the compound rather than relying on a generic description. Key information may include silicone type, nominal hardness, operating temperature range, tensile strength, elongation, compression set and resistance to ageing. A low compression set is particularly important because the gasket must maintain contact pressure after years of compression, relaxation and frame movement.

Hardness should suit the profile and the joint geometry. A gasket that is too soft may roll, stretch or extrude during installation; one that is too hard may resist insertion and fail to accommodate manufacturing tolerances. The required compression range should be stated on the shop drawings, with the profile supplier’s installation data used to confirm the acceptable minimum and maximum.

Colour and finish also deserve consideration. Black silicone is common because it hides dirt and offers strong resistance to visible degradation, but other colours may be required for architectural reasons. The selected colour should not be treated as proof of performance. Product certification, batch consistency and compatibility testing are more important than appearance.

Detail movement, corners and tolerances

Curtain wall joints move as a result of thermal expansion, building deflection, wind pressure, glass tolerances and differential movement between materials. Australian wind conditions can be demanding, particularly in exposed coastal sites and cyclonic regions. The facade engineer should establish design actions and movement limits before the gasket profile is finalised.

Joint movement must be considered in three dimensions. A gasket may accommodate compression across the glazing pocket while having limited capacity for shear or longitudinal movement. If the frame design allows the glass to shift relative to the aluminium, the gasket needs to retain contact without twisting or pulling away from its seating groove.

Corners are frequent sources of leakage because a straight gasket cannot simply be folded tightly without creating stress or a gap. The preferred solution may be a factory-vulcanised corner, moulded corner insert or carefully controlled mitre joint, depending on the proprietary system. The detail should identify the joining method, adhesive or sealant, surface preparation and curing requirements.

Tolerances should cover frame fabrication, glass thickness, glass edge quality and site alignment. A gasket profile that performs perfectly at nominal dimensions can fail when the glass is near the tolerance limit. Shop drawings should show rebate dimensions, bite, pocket depth, gasket seating and allowable deviation. If the facade includes rainscreen panels or complex cladding transitions, early panel layout coordination can also reduce awkward junctions that place extra stress on curtain wall seals.

Control compatibility at every interface

Silicone gaskets contact more than glass and aluminium. They may meet powder coatings, anodised finishes, thermal breaks, setting blocks, glazing tapes, backing materials, sealants, paints and cleaning chemicals. Compatibility must be confirmed for the complete assembly, not just for the gasket in isolation.

A gasket can soften, swell, stain or lose adhesion when exposed to an incompatible substance. Plasticisers and oils from adjacent materials may migrate into the silicone, while aggressive cleaners can affect surface treatments or leave residues that prevent a secondary sealant from bonding. Product data sheets should be reviewed together, and representative samples should be tested where the combination is unusual.

The specification should state whether a silicone-compatible lubricant is allowed during installation. Lubricants can ease insertion but may contaminate bonding surfaces or migrate into drainage cavities. If a separate silicone seal is applied at a gasket splice, the sealant manufacturer should confirm adhesion to the exact gasket compound and frame finish.

Adjacent waterproofing details need the same discipline. At podiums, balconies and roof interfaces, curtain wall drainage should connect with membranes, flashings and thresholds without creating a capillary bridge. Where floor finishes or hard surfaces meet the facade, the interface should be coordinated with the waterproofing design; a flooring systems resource can provide useful context when reviewing adjoining surface build-ups and movement joints.

Verify installation and test the completed facade

Even a well-designed gasket can leak if it is stretched, cut too short, installed with the wrong orientation or damaged during glazing. Installation instructions should state whether the gasket is to be installed dry, lubricated, pre-cut or continuous. Workers should avoid stretching the material around corners because it can shrink back and open a gap after installation.

Inspection should include gasket seating, compression, splice quality, corner continuity, glass edge contact and clear drainage openings. A simple visual check can identify rolled sections, fish mouths, trapped debris and areas where the gasket has pulled out of its channel. Photographic records at representative bays are valuable before pressure plates, snap caps or internal finishes conceal the work.

Laboratory testing and site testing should reflect the project’s exposure and performance requirements. Facade testing may include air infiltration, static water penetration and dynamic water testing, with the procedure agreed between the facade consultant, contractor and certifier. Australian projects commonly refer to relevant requirements under AS 2047 and AS/NZS 4284, while wind design must align with the applicable provisions of AS/NZS 1170, including regional conditions and site exposure.

Testing should occur early enough to correct a detail rather than merely document a failure. If water appears at an internal mullion, the investigation should trace the path through the drainage cavity, gasket joints, pressure plate seals and adjacent interfaces. Replacing an isolated length of gasket without finding the entry route can leave the underlying defect unresolved.

Project handover should include product information, approved shop drawings, test records, cleaning instructions and maintenance guidance. A practical maintenance regime can identify displaced gaskets, failed corner seals, blocked weeps and damage caused by later trades. This documentation gives property owners and facilities teams a clear basis for monitoring the curtain wall throughout its service life.